Please find content of Webasto Accessories page below
Thermoduct Ducting Insulation
Thermoduct ducting insulation can help prevent up to 40% heat loss through ducting pipes. The hot air pipes can get up to 100ºC some cases and therefore Thermoduct can also act as a protective covering.
Thermoduct Ducting Insulation
Thermoduct ducting insulation, has a wipe clean, heavy duty outer cover, with a 25mm thick, 3MTMThinsulateTM inner core.
Available in 75cm lengths that slip over a variety of ducting diameters, Thermoduct won’t absorb water, hard wearing and with an R4 insulation rating is capable of reducing the outer duct temperature from +100ºC to +30ºC.
Adding Thermoduct insulation adds less than 10% to the cost of a modern warm air heating system and can improve the heaters actual performance by up to 50%.
Available in four sizes to meet the needs of every instalation (see options below)
|Thermoduct with 3MTMThinsulateTM 60mm i.d. x 75cm (for 55mm & 60mm Ducting)|
|Thermoduct with 3MTMThinsulateTM 80mm i.d. x 75cm (For 75mm & 80mm Ducting)|
|Thermoduct with 3MTMThinsulateTM 100mm i.d. x 75cm (For 90mm & 100mm Ducting)|
Indel-Webasto Isotemp Calorifier tanks
In order to create domestic hot water with a Webasto Thermo water heating system you require to install a calorifier tank, we offer teh Indel-Webasto Isotemp range of tanks.
Isotemp Basic has an exclusive look, with its brushed stainless steel cover, but most important is the internal design. The highest capacity is achieved by the engine water heat exchanger as well as the immersion heater placement. They are positioned in the lowest part of the tank where the water is coldest, to really heat all the water in the tank, which grants an outstanding volume of hot water. The water in- and outlets are also designed for a minimal mixing of cold water into thee hot, by the incoming water. The selected materials are all the best; tank, tubes and all materials in contact with the water are made of acid proof stainless steel AISI 316 and welded with protection gas to eliminate any risk of corrosion. Each water heater is individually leakage tested to 16 bar/230 psi, before delivery.
|Product name||Dimensions LxD mm||Immersion heater||Volume (l)||Weight (kg)||Max pressure bar|
|Basic 24||460×395 mm||750W – 230V||24||14||7.0|
|Basic 30||525×395 mm||750W – 230V||30||17||7.0|
|Basic 40||630×395 mm||750W – 230V||40||20||7.0|
|Basic 40||630×395 mm||750W – 230V||40||22||7.0|
|Basic 50||845×395 mm||750W – 230V||50||23||7.0|
|Basic 75||1040×395 mm||750W – 230V||75||29||7.0|
|Basic 75 DS||1040×395 mm||750W – 230V||75||31||7.0|
Isotemp Slim is a range of water heaters, available in three sizes, 15, 20 and 25 litres. Isotemp Slim has an exlusive look and design, with brushed stainless steel cover. The highest capacity is achieved by the engine water heat exchanger, as well as by the immersion heater mounting. They are positioned as low as possible inside the tank to heat the water where it is coldest.
|Product name||Dimensions LxD mm||Volume (l)||Immersion heater||Weight (kg)||Temperature range|
|Slim 15||505×295 mm||15||750W – 230V||10.5||7.0|
|Slim 20||630×295 mm||20||750W – 230V||11.5||7.0|
|Slim 25||750×295 mm||25||750W – 230V||13.5||7.0|
Isotemp Slim Square
Indel Marine has intruduced a slim line, box style water heater to its range, which has been designed for easy installation in narrow spaces om board. The Isotemp Slim Square has a 16 litres capacity, quick and effectively heats water up via the boat engine or by the electrical heater element if the boat is connected to shore power. The water is heated to above 70ºC which enables water to be heated on board at the correct levels from both hygiene and safety purpose.
It can be installed in a varity of position, making it more vesatile than standard models currently available. As with all Isotemp water heaters, the Isotemp Slim square has been constructed with a robust acid proof stainless steel (AISIS 316) and fitted with special components to protect it from overheating. All electrical installations are fatory made and delivered with a cable and plug.
It also features a safety valve for 5.5 bars with a built-in two-way check valve, which reduces or prevents spill water by expansion. It also has a winter drain function. Thermostat mixing valve can be mounted as an option. The safety valve is set to 5.5 bar/80 psi on this model.
|Product name||Volume (l)||Weight (kg)||Max pressure bar||Immersion heater||Dimensions||HxWxD (mm)|
|Slim Square||16||16||16||5.5||750W – 230V||400x180x575|